Note: This message is displayed if (1) your browser is not standards-compliant or (2) you have you disabled CSS. Read our Policies for more information.
The IDEM Watershed Management Plan (WMP) Checklist (2009) requires groups to identify targets for water quality parameters of concern. A target is defined as the desired measured level of a water quality or habitat/biological parameter that a group has decided streams in the watershed should meet.
Where an Indiana Water Quality Standard or TMDL exists for a parameter of concern, the watershed group must, at a minimum, set the target to meet the respective standard or the loading limit set in the TMDL. Groups obviously are welcome to set more stringent targets if they wish. Figure 1 shows water quality parameters watershed groups are often concerned with and which have an Indiana Water Quality Standard. A complete list of Indiana’s Water Quality Standards can be found in the Indiana Administrative Code.
Many of the water quality parameters watershed groups are concerned with do not have a standard. In these instances groups are free to set whatever target they deem appropriate, but that freedom can be overwhelming given the myriad of targets being used across the county. This guidance does not attempt to tell watershed groups what targets to choose, but rather, lists in Figure 2 several targets used by other watershed groups in Indiana and the source of those targets. IDEM hopes this information helps watershed groups wisely choose water quality targets for their specific watershed.
|Total Ammonia (NH3)||Range between 0.0 and 0.21 mg/L depending upon temperature and pH||Indiana Administrative Code (327 IAC 2-1-6)|
|Atrazine||Max: 3.0 ppb||U.S. EPA Drinking Water Standard|
|Dissolved Oxygen (DO)||Min: 4.0 mg/L Max: 12.0 mg/L||Indiana Administrative Code (327 IAC 2-1-6)|
|Min: 6.0 mg/L in coldwater fishery streams||Indiana Administrative Code (327 IAC 2-1.5-8)|
|Min: 7.0 mg/L in spawning areas of coldwater fishery streams||Indiana Administrative Code (327 IAC 2-1.5-8)|
|E. coli||Max: 235 CFU/ 100mL in a single sample||Indiana Administrative Code (327 IAC 2-1.5-8)|
|Max: Geometric Mean of 125 CFU/ 100mL from 5 equally spaced samples over a 30-day period||Indiana Administrative Code (327 IAC 2-1.5-8)|
|Nitrate||Max: 10 mg/L in waters designated as a drinking water source||Indiana Administrative Code (327 IAC 2-1-6)|
|Nitrite||Max: 1 mg/L in waters designated as a drinking water source||Indiana Administrative Code (327 IAC 2-1-6)|
|Nitrate-N + Nitrate-N||Max: 10 mg/L in waters designated as a drinking water source||Indiana Administrative Code (327 IAC 2-1-6)|
|Temperature||Dependant on time of year and whether stream is designated as a cold water fisheries||Indiana Administrative Code (327 IAC 2-1-6)|
|Nitrate-nitrogen (NO3)||Max: 0.633 mg/L||U.S. EPA recommendation *|
|Max: 1.0 mg/L||Ohio EPA recommended criteria for Warm Water Habitat (WWH) headwater streams in Ohio EPA Technical Bulletin MAS//1999-1-1 [PDF]|
|1.5 mg/L||Dividing line between mesotrophic and eutrophic streams (Dodds, W.K. et al., 1998, Table 1, pg. 1459, and in EPA-822-B-00-002 [PDF], p 27.)|
|10.0 mg/L||IDEM draft TMDL target based on drinking water targets|
also known as Soluble reactive phosphorus (SRP)
|Max: 0.005 mg/L||Wawasee Area Conservancy Foundation recommendation for lake systems, NESWP344|
|Suspended Sediment Concentration (SSC)||Max: 25.0 mg/L||U.S. EPA recommendation for excellent fisheries|
|Range: 25.0-80.0 mg/L||U.S. EPA recommendation for good to moderate fisheries|
|Total Kjeldahl Nitrogen (TKN)||Max: 0.591 mg/L||U.S. EPA recommendation *|
|Total Phosphorus||Max: 0.076 mg/L||U.S. EPA recommendation|
|0.07 mg/L||Dividing line between mesotrophic and eutrophic streams (Dodds, W.K. et al., 1998, Table 1, pg. 1459, and in EPA-822-B-00-002 [PDF], p 27.)|
|Max: 0.08 mg/L||Ohio EPA recommended criteria for Warm Water Habitat (WWH) headwater streams in Ohio EPA Technical Bulletin MAS//1999-1-1 [PDF]|
|Max: 0.3 mg/L||IDEM draft TMDL target|
|Total Suspended Solids (TSS)||Max: 80.0 mg/L||Wawasee Area Conservancy Foundation recommendation to protect aquatic life in lake systems|
|Max: 30.0 mg/L||IDEM draft TMDL target from NPDES rule for lake dischargers in 327 IAC 5-10-4 re: monthly average for winter limits for small sanitary treatment plants|
|Range: 25.0-80.0 mg/L||Concentrations within this range reduce fish concentrations (Waters, T.F.,, 1995). Sediment in streams: sources, biological effects and control. American Fisheries Society, Bethesda, MD. 251 p.|
|Max: 40.0 mg/L||New Jersey criteria for warm water streams|
|Max: 46.0 mg/L||Minnesota TMDL criteria for protection of fish/macroinvertebrate health|
|Turbidity||Max: 25.0 NTU||Minnesota TMDL criteria for protection of fish/macroinvertebrate health|
|Max: 10.4 NTU||U.S. EPA recommendation|
* U.S. EPA recommended criteria are different for parts of southwest Indiana within Ecoregion IX. See Ecoregional Nutrient Criteria Documents for Rivers & Streams for more information.
Geometric Mean: The geometric mean, in mathematics, is a type of mean or average, which indicates the central tendency or typical value of a set of numbers. It is similar to the arithmetic mean, which is what most people think of with the word "average," except that instead of adding the set of numbers and then dividing the sum by the count of numbers in the set, n, the numbers are multiplied and then the nth root of the resulting product is taken. A geometric mean, unlike an arithmetic mean, tends to dampen the effect of very high or low values, which might bias the mean if a straight average (arithmetic mean) were calculated. This is helpful when analyzing bacteria concentrations, because levels may vary anywhere from 10 to 10,000 fold over a given period.
Geometric Mean Formula:
Geometric Mean = ((X1)*(X2)*(X3)*.......(XN))^1/N
X = Individual score
N = Sample size (Number of scores)
Geometric Mean Example:
Use the following set of values - 1, 2, 3, 4, and 5 to find the Geometric Mean.
The Indiana Administrative Code uses the Geometric Mean as a calculation for five evenly spaced samples of E. coli over 30-days in order to determine compliance with the water quality standard.
In Microsoft Excel, the equation for geomean is =Geomean(Xx:Yy)